How to Cut 45 Degree Angle Without Table Saw?

Woodworking has never been easier thanks to wood cutting tools. And for cutting at a 45-degree angle, a table saw is the most accurate tool. 

However, a table saw needs a large enough workspace. Now, you’re wondering if there’s another tool out there that can help you the same.

So, how to cut a 45-degree angle without a table saw?

You can also use other tools to cut a 45-degree angle. But in order to measure the 45 degree angle, you must use a speed square. You can use hand tools like a hacksaw or handsaw. There’re several solutions available if you prefer using power tools for cutting. Like a chainsaw, circular saw, etc.

But is it sufficient to simply use tools to create a 45-degree angle? Believe me, it also needs other things, like the method and some techniques. To know those things, you must read the entire article. 

How to Use a Speed Square for 45 Degree Angle?

You probably noticed that every woodworker must keep a triangle square in their tool belt. This handy tool is called by multiple names like a rafter square or a speed square.

It can be used for more than just marking 90 and 45-degree angles while cutting 2x4s. It can be used to guide your circular saw and more. A speed square can be used to mark any angle between 0 and 90 degrees.

In addition to marking, measuring, and saw guiding with a speed square. Knowing how to use it isn’t enough. It will need to be done safely and with the appropriate precautions.

Also, choosing the best tools for woodworking, make your work half done. 

To Make Straight Cut as a Saw Guide

The speed square’s most important use is as a saw guide. First, mark the board where you wish to cut using a 45-degree line.

Now, position your saw such that the cut line is parallel to the blade’s teeth. 

To act as a fence, hold the speed square up against the shoe of the saw. Be cautious to maintain a constant distance between the saw blade and the cut line. 

You do the work done with a 6” model. However, it’s better to use a 12″ speed square. Due to its extra length, the saw will have more fences to ride against. 

Best Tool to Cut Wood

There are alternative tools that can help you. Since you cannot use a table saw due to not working properly. Or perhaps you already have that tool in your toolbox. 

For every job that calls for cutting wood, there is a suitable tool. You can cut different angles for your project using both hand and power tools. 

Today, I’ll share some tools with you that can help you cut wood 45-degree angle. Many innovative technologies are used to make wood cutting tools. So, knowing which tools to use and how they work has become important. 

For particular jobs, different saws are developed. Using the right saw will save you time and energy. As well as a stunning finish for the final result. 

So, let’s get down to the business. Here’re some tools that you can use in place of a table saw to cut 45-degree angles.

Hand Tools Used for Cutting Wood

Hand saws are the standard and necessary tool among the other wood cutting tools. These can be available very easily and are budget-friendly as well. There are several different hand saws that can be used for a variety of tasks.

The teeth of hand saws are made of steel, iron, and other metals, and they require manual labor. 

Hand tools come in very handy to complete your project when cutting 45-degree angles. Simply use a speed square to mark the angle. Before cutting it, ensure a clean 45-degree angle cut.

Let’s find out which hand saw tools will make your job done easily. 

1. Crosscut Saw

When manually cutting wood across the grain, a crosscut saw is an ideal tool. It has a wood cutting blade with a handle. Many cutting teeth with alternate cutting edges are placed between the heel and toe.

With one edge of each cutting tooth, sawdust is extracted. While the other edge pushes it out. On crosscut saws, there are 8 to 15 pointed teeth per inch.

To cut in order to use a crosscut saw securely, draw a straight line on the wood. Hold the wood firmly or tie it so that it won’t move while you’re cutting.

Put the saw’s central teeth on the line across from you. To start the cut, swiftly push it. Once the process of cutting has started. To make sure the cut stays on the line, push and pull the saw.

As you cut the wood, check to make sure the end is held. So it won’t split under the weight of the blade. For best cuts and safety, keep your crosscut saw sharp.

2. Hack Saw

Any DIY toolkit should include a hacksaw because of its many uses. Pipes and other materials can be cut using it. When used to saw a log, it is lightweight and portable. 

So, as always, measure and mark the place you want to cut. After that, secure the item. To attach wood to your work surface, use a clamp. 

Choose the right blade. Use blades with large teeth. Use a short stroke and start gradually cutting at the mark. 

Continue cutting away from you with strong and steady strokes. Hacksaw blades are relatively thin, therefore they could break when cutting. Just take the broken blade out, replace it, then tighten the adjuster. 

Besides handsaws, to increase efficiency and save time, power saws are very popular for wood cutting. So, let’s get to it.

3. Power Tools for Cutting Wood

Power saws have the key benefit of being able to quickly. And they easily cut a large amount of wood. They are classified as electric saws because of their rechargeable battery.

Power saws are faster than hand saws and require less labor than hand saws. Depending on the cut, they can fit with different kinds of blades. 

If you’re searching for the best blade to cut wood perfectly, you can use these products. 

Besides the table saw, you can use other power tools to cut the 45-degree angle. Let’s then look at the tools you can use for accurate and ideal angle cutting. 

4. Circular Saw

When cutting 45-degree angle wood, accuracy is crucial. Keep an eye on the moving blades to prevent cuts from straying off the cut line. 

With its lip extending over the edge, put a speed square over the board you are cutting. Find the cut line and align the blade with it. Slide the speed square’s straight edge up against the saw shoe.

The use of a saw guide can keep you on the course when making longer rip cuts. Such as Sheets of plywood. 

Set the blade depth no more than 1/4-inch below the board thickness for efficiency and safety.

5. Jigsaw

The jigsaw is a powerful and simple-to-use power tool. It allows for making straight or complicated curved cuts. You can cut more precisely by using a good jigsaw

First, firmly clamp the material to a work surface. Attach the proper blade. Then

connect the saw’s cord to a power source or install its batteries. 

Place the saw shoe close to the cutting line and on the edge of the material. During this time, the blade is near the workpiece but not touching it. To start the saw at full speed, pull the trigger.

Hold the shoe firmly in place and slowly advance the saw to the cutting line. Move the saw along the cutting line’s edge while maintaining a flat shoe.

Release the trigger once you’ve finished cutting to stop the blade. Lift the saw up and set it down on the workstation.

6. Reciprocating Saw

When it comes to cutting wood, a reciprocating saw is a handy tool. With a trigger on the handle, a reciprocating saw is a small, portable electric saw. And with a horizontal blade coming out of the saw’s end.

Putting the right blade on a reciprocating saw is the first step of using it. Choose a blade that is at least two inches longer than the depth of the material.

Turn off the saw’s power supply, and lift the blade release. And then move the blade into position. 

Make sure the blade is firmly in place before reconnecting the power. To best fit the blade and the cut, the shoe should be adjusted. For a quicker, more forceful cut, you can increase the saw’s orbital movement.

Put the other hand around the handle and your dominant hand around the front grip. When necessary, try to avoid using just one hand to operate the saw.

Place the blade on the wood. And firmly press the shoe against it to begin the cut.

Pull the trigger slowly. Then, until the cut is finished, gradually increase the speed of the blade. And keep a firm hold of the saw.

FAQs

Can a jigsaw cut through thick Wood?

Yes, you can use a jigsaw to cut thick wood. Jigsaws are often used to cut softwood that is no thicker than 1-1/2 inches. But they can also cut hardwood up to 34 inches thick. Jigsaw blades frequently bend when cutting bends in heavier boards. It creates a beveled edge as opposed to a square one.

How Do You Cut HardWood?

A rip blade is the ideal saw blade for ripping hardwood. It is particularly designed to cut through the fibers of the wood. It will effortlessly cut through hardwood and leave a clean edge. Typically, rip blades have between 10 and 40 flat-topped teeth.

How Do You Work Out A 45 Degree Angle?

In comparison to a straight angle, which is 90 degrees, a 45-degree angle is half the size. Without using any special tools, make the angle using a ruler and a square. Or another object that forms a right angle.

Conclusion

So, now you can the way how to 45 angle degrees without a table saw. In case, you have a smaller space or an insufficient budget. You can decide which of these tools is most practical for you.

All of them are simple to deal with and will provide the same result for you. However, safety should always come first. To avoid the risks, wear the appropriate safety gear.

Leave a Comment

Your email address will not be published.