Setting the right angle on a table saw can seem difficult to you. We can understand that. However, if you know how to set angles it will be easier for you.
So, how to cut a 22.5-degree angle on table saw?
Firstly, use a carpenter’s square mark to create a right-angled mark across your wood. Then set your blade angle to 67.55 degrees to get 22.5 degrees. Lastly, after getting the 22.5 angles, cut the wood piece on the table saw.
Now, these are some basic info which isn’t enough for you. We have provided you detailed info below with some tips and tricks.
Therefore, we hope you’ll continue reading till the end!
SKIP AHEAD
Cutting a 22.5 Degree Angle on Table Saw – Explained
Well, the most common method of cutting your timber is marking it and cutting it. However, if you don’t have the experience you will mess things up.
But by using a table saw you can cut at a 22.5-degree angle easily. Thus, the table saw is a smart choice while cutting wood is needed.
Now, here are some steps to follow while cutting 22.5 angles on the table saw-
Gather the Necessary Tools
Before starting the cutting process, you’ll need some tools-
- Precise measuring rule
- Sharp pencil
- Carpenter’s square
- Safety Glasses
- Gloves
- Table Saw
Grab all the materials needed and get to it!
Step 1 of 3: Using a Carpenter’s Square to Mark on Head Side
A carpenter’s square will permit you to make a right-angled mark over your timber. Also, if you want, you can utilize an engineer’s square or a triangle too.
Now, you need to hold the “stock” or handle of the square tightly. Hold it against the wood while marking it. You should locate the tip of the pencil on the mark you made at first when measuring.
After that, slide the square so that it bumps against the tip. And markdown the square.
Step 2 of 3: Setting the Blade Angle
Here, you need to set the blade angle to 67.5 degrees. The vertical angle should be 90 degrees tilt to the blade at 22.5 degrees. And the remaining angle should be the bevel angle.
Remember you need to set these angles properly between table and blade. Also, make sure the saw has a ZCI. Because it translates to higher accuracy with your cuts.
Apart from this, you need to fasten an atoning fence to the saw’s fence. That’s it! you’re ready for your desired angle cut.
Step 3 of 3: Cutting Your Desired Angle
Now, stand on the right side of the table saw. Put on your safety glasses and gloves. Hold the wood piece in place and start cutting it on the table saw.
Also, to help you out on the gloves, here are some of our suggestions-
So, use the gloves and keep your hands safe while cutting!
Alternative to Table Saw: Cutting 22.5 Degree Angle with Miter Saw
A miter saw is one of the powerful tools in wooden boards. When it’s about cutting various angles miter saw does the work easily.
Plus the miter saw takes less time while cutting. Therefore, if you think the table saw isn’t for you, try this option!
Now, to cut a 22.5 angle with your miter saw, follow our lead-
At first, you need to grab the miter handle/lock. Then pull the lever underneath it.
Now, carefully eye the miter scale. Make a move to your turntable to the left or the right. Remember, you need to move it till you get it to the desired angle on the miter scale.
There will be a small arrow that will specify you at the angle. In this way, you need to reach the 22.5-degrees angle.
Next, you need to locate a piece of wood on the fence. Then use the vise to brace it into the right place.
Don’t have a vise?
You can use your hands to press it firmly against the fence. Also, when you’re cutting it make sure there is no jiggle in the wood. Else, it’ll be imperfect.
Now, you have the wood in the region. So you can press the trigger, and move the handle down. This will cut the wood at the desired angle of your option.
Important Tips When Cutting with Table Saw
Well, you may face some difficulties while cutting or using the table saw. So, we’ve offered you some tips and tricks. Following these, you can solve your difficulties-
- Firstly, plywoods tend to droop under the table saw fence. Thus, clamp a shortboard under the fence to avoid drooping plywoods.
- Remember, do not cut the boards that have a bumpy edge, bowed, or rough edge. Because these boards are dangerous to cut on a table saw.
- Then use an old Work-Mate or close to floor-standing tool holder as an out-feed table. It’ll help to hold wood easily as it comes off the saw.
- Use a riving knife to protect the wood from getting caught in the back of the saw.
That’s it! These tips will assuredly make your table saw safer and easier to use.
Frequently Asked Questions
Question: What type of stock should you never rip on the table saw?
Answer: Well, you should not rip round stock on a table saw. While making bevel cuts, keep your hands and stock to the right of the table saw.
Question: Where should you stand while managing a table saw?
Answer: Here, the best place to stand while managing a table saw is to the left of the blade. It’s best to stand in a position that is natural and cozy for you.
Question: What should you not do with the table saw?
Answer: Well, you should avoid doing freehand cuts on the table saw. You should guide the stock through the blade. Also, use the rip fence or the miter gauge.
Take Away
So, that’s all you need to know. Now you have a clear idea about how to cut a 22.5 degree angle on table saw.
Well, a safety tip for you-
It’s better not to use the table saw rip fence as a guide for cutting wood to length. Be careful while doing it. Good Luck!
- How To Hide A Shed From HOA (5 Easy Hacks) - September 8, 2023
- How to Hang Tools in a Suncast Shed (7 Easy Steps) - August 31, 2023
- How To Hang Stuff In Resin Sheds (5 Easy Steps) - August 29, 2023